Medusa Mirror Project - Trailblazers Home School

Medusa Mirror: PowerSwitch Build and Install Instructions for Customer

Richard — Sat, 27 Apr 2024 05:58:42 +0000

I custom design a power switch for the Medusa Backlit Mirror using TinkerCAD, a 3D printer, some hot glue and solder.

The post Medusa Mirror: PowerSwitch Build and Install Instructions for Customer first appeared on Trailblazers Home School.

Medusa Mirror project

Richard — Thu, 11 Apr 2024 10:07:09 +0000

What did you do for the eclipse? Me, I was outside cleaning a mirror. Seems only right to be working on Medusa during an eclipse. It was crazy. Some large bird started screeching for like 15 minutes straight. Definitely spooky. https://avxpro.org/wp-content/uploads/2024/04/solar-eclips.mp4 And I’ve backlit it with the eclipse for customer approval. i’ve decided to finish the piece regardless. I can’t easily describe the machines I’ve had to build / upgrade… new techs I’ve had to learn to bring this to life. so this piece is a triumph for me. If the customer doesn’t like it due to print issues, no worries, I’ll make another for her and finish this one for myself. Hell, I might even hang it in the shop in place of my AVXpro sign. 4/9/2024 apply vinyl Always good to get Zilla back on the wall. My shop is small so it’s really hard to work around the machine while it’s down. I haven’t seen my workbench for awhile. It’s a good to see it again! You like my sexy legs? Oh yeahhhh 😛 I’m going to heat the mirror: so I’ll elevate it off the table with these M5 nuts. (I don’t need it high). And some cotton over the nuts to prevent scratching. I ran out of vinyl 🙁 BOO!!! Not really worth turning the iron on if i don’t have enough to complete the job… So I covered it with plastic, ordered the stuff I need and hopefully it’ll be in tomorrow. 4/10/2024 apply vinyl New stuff came in ontime. Fake it till you make it…. This… SHOULD… work…. Mirror cracked from the heat It was my fault, not the process. I got complacent and stayed in one area too long. Crack runs pretty far out, breaking off two corners. This is less than ideal but not a dealbreaker. Customer wants the mirror cracked in the end result, so the more cracks the better. Problem is: I’ll have to figure out a way to flip a large mirror that is no longer structurally sound. I’ll figure it out later. vinyl is in place, bonded good. Now to just remove the clear shiny backer and good to go. Shit. I’ll admit. I was cussing. It was like the glue between the clear and the vinyl was way tougher than it needed to be. Vinyl stretched and delaminated from the mirror. Now what??? Can I laminate by touching the iron directly to the vinyl without the clear protection? Yes. Yes I can. But I’ve got to be careful. Ok. I can do that. I can be careful. And done! Looks good. 4/11/2024 Flip, hit, and repair.

The post Medusa Mirror project first appeared on Trailblazers Home School.

Update on the mirror setup from yesterday

Richard — Thu, 28 Mar 2024 14:30:33 +0000

Update on the setup from yesterday. All I can say is “wow”. At these settings, I knew it was going to take forever but mannnnn is it worth it! The piece is incredible. There’s a small glitch where I had a belt skip some teeth… NEW MACHINE IS TEETHING!!!!! haha. I made a dad joke. But seriously, the customer intends to break this mirror so I think my booboo will be welcomed to the project.

The post Update on the mirror setup from yesterday first appeared on Trailblazers Home School.

Some pictures of the process (for a friend)

Richard — Wed, 27 Mar 2024 18:42:14 +0000

A friend of mine, DC, asked me if I could share some pictures of what I do for his daughter. I’d be happy to. Here’s a typical setup: The work starts in photoshop like normal (This is GIMP. It’s free. I’m cheap.) It’ll go to imag-r.com to do the dither. GIMP can do a dither, but it imag-r looks better. See how it’s all dots on the screen now? Anyways, this is a small swatch, a point of interest that has been moved into the software that controls the laser. In this case we are doing a Medusa mirror so we are looking at a snake head that has both lights in the head and darks in the neck…. full spectrum of “color” if you will. If we can make out the curvature of the head and still be able to see the neck in our test, we’re good to go. Easy peasy right? So we’ll run a few copies of the swatch… making educated guesses to change the settings into focus with each one. writing each change and observations as we go…. This is the machine running the project by the way. It was custom built specifically for this particular Medusa mirror job. The rails are 1200mm, 47.2 inches. Back to finding our settings: I stow this light thing on the ceiling when not in use. I think it’s an artist’s tracing light. I don’t know. My Aunt Karen got it for me so shop ID = “Karen”. I use it all the time. Here is our target: I think number two from the right is going to be our best bet. The first one from the right is over-burnt and you can’t really tell the details of the neck in any of the others. The second one seems just right. You can barely tell the head and you can see the neck. A good compromise. So….. It’s just a matter of checking back to our notes and here’s our settings. Good to go! Now it’s just a matter of framing it. I’m just tracing the outline of the project right now and lining up the mirror to where the machine thinks the mirror is. I usually trace the very exterior of the piece so that the laser is half on / half off the edge. I find there’s less margin for error that way. AND BURN. A COUPLE OF HOURS INTO THE BURN: Progress looks good. I believe I’m seeing the aluminum foil bed through the glass so that’s a good sign! This one’s “quality over quantity” so check back in a few days. I’ll be sure to update. Thanks for reading.

The post Some pictures of the process (for a friend) first appeared on Trailblazers Home School.